- Converts Schrader rims to Presta - Rubber - Sold individually

- Shell: 8mm flanged axle nut - Flanged

Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.

- For square taper and flanged. - Fits most cartridge BBs - Shell: 8mm Flanged axle bolt

- Steel end nut for QR skewers

Rubber rim strips for 24-inch diameter fatbike rims. - Sold individually

Replacement clear plastic spoke guard.

- Eady to install - Spoke mounted - 2 per set

- Strong nylon reinforced PVC for a secure fit - Handles high-pressures; does not rot - 0.5mm thick

- Replacement rear skewer - Spacing: 135mm - Material: Steel

• Replacement aluminum quick release skewers

- Plastic spoke covers in a variety of colors - 300mm cut to fit length - 36 pieces - enough for one wheel - Increases visibility and demands attention

• Replacement aluminum quick release skewers

- Variable widths - Left: 32mm - Center: 52mm - Right: 35mm - Length: 119mm - Overall: 140mm

- Strong nylon reinforced material handles high-pressures - Adhesive backed for a secure fit - Does not rot - 0.5mm thick

Aluminum Tubeless Presta Valve - MTB or Road

Tubeless valves for DT Swiss rims for repair or replacement.

- Strong nylon reinforced material handles high-pressures - Adhesive backed for a secure fit - Does not rot - 0.5mm thick

- Green colored spoke prep remains pliable for adjustments - Helps keep spoke nipples from loosening

Pro Head Reinforcement System (PHR) has a larger and more spherical contact area and is designed to balance loads transferred to the rim. The PHR system acts as a ball and socket interface, allowing the spoke to pivot into alignment while maintaining even, consistent contact during installation in order to follow the perfect trajectory from the hub to the rim.

Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.

- End cap adapters for Origin8 RD1120 series 11-speed road hubs

Stan's 3.30/3.30Ti Hub Kit converts Stan's 3.30 front hubs from quick-release to through-axle compatible. Installation is easy—just pull the old ones off and put the new ones on. Conversion kits available in 12mm and 15mm.

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

- Extra security against theft - 5mm hex CrMo axle

- AL6061 alloy tubeless Presta valve - Includes 2 O-rings, one standard profile and one aero profile, for an airtight seal on any rim - Removable valve core for installing sealant - Additional replacement valve cores sold separately - Sold individually

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

DT-Swiss Center Lock Adaptor. Allows 6-bolt rotors to be used on Center Lock hubs. - Rotor thickness between 1.8mm and 2.2mm - Easy assembly and only 29g - Made in Switzerland by DT Swiss - 230mm version accepts all rotors up to 203mm diameter - 160mm version accepts all rotors up to 160mm diameter